WeChat: +86.13328318872 | Home | InSite Search | About Us | Contact Us |
Stearic
Acid
|
Medical Dental Grade TPI Granules, Synthetic Gutta Percha, Trans PolyIsoprene, TPI, Trans Isoprene Rubber, Trans-1,4-PolyIsoprene | V-Belts | China Largest Manufacturer of Meteorological Balloons | |||||
Rimpex@RPM supplies stearic acid with grade 1800, 1802, 1840, 1850.
PRODUCT DESCRIPTION: | RUBBER GRADE STEARIC ACID |
||
PRODUCT CODE: | 1800 |
||
SPECIFICATION NO.: |
- |
||
PARAMETERS | SPECIFICATION |
METHODS |
|
ACID VALUE, mg KOH/g | - |
195 - 216 |
AOCS Te 1a - 64 |
SAPONIFICATION VALUE, mg KOH/g | - |
196 - 217 |
AOCS Tl 1a - 64 |
IODINE VALUE, g I2/ 100 g | - |
6.0 MAX |
AOCS Tg 1 - 64 |
TITER, °C | - |
50 MIN |
AOCS Cc 12 - 59 |
COLOUR, GARDNER 1963 | - |
4 MAX |
- |
COLOUR, LOVIBOND 5.25" | RED |
3.5 MAX |
AOCS Cc 13e - 92 |
YELLOW |
15.0 MAX |
- |
|
ISSUED IN 1998. |
1. | COMPOSITION INFORMATION ON INGREDIENT(S) | |
Product Description : Product Code : Component : Chemical Formula : CAS No. : IUPAC Name : Exposure Guidelines : |
Rubber Grade Stearic Acid 1800 Fatty Acid, C16 - C18 CH3(CH2)nCOOH Hexadecanoic Acid - Octadecanoic Acid Mix Not Established |
|
2. | PHYSICAL CHEMICAL CHARACTERISTICS | |
Boiling Point : Freezing Point : Specific Gravity : Vapour Pressure : Vapour Density : Solubility : Appearance and Odor : |
~ 291 °C, 100 mmHg 50 - 62 °C 0.84 ( 80 °C ) Not applicable Not applicable Insoluble in water Soluble in alcohols, ethers, chloroform and acetone. White flake with slightly fatty oil like odor. |
|
3. | FIRE AND EXPLOSION HAZARD DATA | |
Flash Point ( Open Cup Method) : ~ Flammable Limit : Extinguishing Media : Special Fire Fighting Procedures : Unusual Fire and Explosion Hazard : |
~ 182 °C Not Applicable Water, Foam, Dry Chemical, CO2. Not Special Procedures None |
|
4. | REACTIVITY DATA | |
Stability : Incompatibility ( Material to Avoid ) : Hazardous Decomposition or By product : Hazardous Polymerization : |
Stable Strong oxidizing agent, Bases. CO on incomplete combusion. Will not Occur. |
|
5. | HEALTH HAZARTD DATA | |
Route(s) of Entry : Health Hazards ( Acute and Chronic ) - Ingestion toxicity : - Skin irritation : - Eye irritation : Carcinogenic : Signs and Symptoms of Exprosure : Emergency and First Aid Procedures - Skin : - Eye : |
None normally encountered. Not determined, Expected to be low. Essentially non irritation or corneal. Mechanical injury only. Solid or dust may cause irritation or corneal injury due to mechanical action. Not Listed on NTP, IARC, OSHA Non normally encountered. Wash affected areas thoroughly with soap and water. Flush with clean, lukewarm water ( Low pressure) occasionally lifting eyelids. |
|
6. | PRECAUTION FOR SAVE HANDLING AND USE | |
Release and Spilled : Waste Disposal Method : Handling : Other Precaution : |
Sweep and mop or collect with vacuum cleaner Controlled burning. Wash thoroughly None. |
|
7. | CONTROL MEASURES | |
Respiratory Protection ( Specify Type ) : Ventilation. - Local Exhaust : - Mechanical ( General ) : Protective Gloves : Eye Protection : Other Protective Clothing or Equipment : Work Hygeienic Practices : |
Dust respirator. Desirable. Desirable. Rubber Goggles None Wash thoroughly after handling. |
|
THE DATA STATED HEREIN ARE BASED ON THE TEST RESULTS OF SIMILAR COMMERCIALLY AVAILABLE PRODUCT AND EXPIRIENCE WHICH THE MANUFACTURER BELIEVES RELIABLE AND ARE SUPPLIED FOR INFORMATION ONLY.THE PRODUCT IS INTENDED FOR SALING TO INDUSTRIAL AND COMMERCIAL CUSTOMERS. THE MANUFACTURER REQUESTS THAT CUSTOMERS INSPECT AND TEST THE PRODUCT BEFORE USE AND SATISFY THEMSELVES AS TO THE CONTENT AND SUITABILITY. |
PRODUCT DESCRIPTION: | DOUBLE PRESSED STEARIC ACID |
||
PRODUCT CODE: | 1802 |
||
SPECIFICATION NO.: |
- |
||
PARAMETERS | SPECIFICATION |
METHODS |
|
ACID VALUE, mg KOH/g | - |
205 - 215 |
AOCS Te 1a - 64 |
SAPONIFICATION VALUE, mg KOH/g | - |
206 - 216 |
AOCS Tl 1a - 64 |
IODINE VALUE, g I2/ 100 g | - |
1.0 MAX |
AOCS Tg 1 - 64 |
TITER, °C | - |
53 - 57 |
AOCS Cc 12 - 59 |
COLOUR, LOVIBOND 5.25" | RED |
0.8 MAX |
AOCS Cc 13e - 92 |
YELLOW |
3.5 MAX |
- |
|
ISSUED IN 1998. |
1. | COMPOSITION INFORMATION ON INGREDIENT(S) | |
Product Description : Product Code : Component : Chemical Formula : CAS No. : IUPAC Name : Exposure Guidelines : |
Double Pressed Stearic Acid 1802 Fatty Acid, C16 - C18 CH3(CH2)nCOOH Hexadecanoic Acid - Octadecanoic Acid Mix Not Established |
|
2. | PHYSICAL CHEMICAL CHARACTERISTICS | |
Boiling Point : Freezing Point : Specific Gravity : Vapour Pressure : Vapour Density : Solubility : Appearance and Odor : |
~ 291 °C, 100 mmHg 54 - 58°C 0.84 ( 80 °C ) Not applicable Not applicable Insoluble in water Soluble in alcohols, ethers, chloroform and acetone. White flake with slightly fatty oil like odor. |
|
3. | FIRE AND EXPLOSION HAZARD DATA | |
Flash Point ( Open Cup Method) : ~ Flammable Limit : Extinguishing Media : Special Fire Fighting Procedures : Unusual Fire and Explosion Hazard : |
~ 182 °C Not Applicable Water, Foam, Dry Chemical, CO2. Not Special Procedures None |
|
4. | REACTIVITY DATA | |
Stability : Incompatibility ( Material to Avoid ) : Hazardous Decomposition or By product : Hazardous Polymerization : |
Stable Strong oxidizing agent, Bases. CO on incomplete combusion. Will not Occur. |
|
5. | HEALTH HAZARTD DATA | |
Route(s) of Entry : Health Hazards ( Acute and Chronic ) - Ingestion toxicity : - Skin irritation : - Eye irritation : Carcinogenic : Signs and Symptoms of Exprosure : Emergency and First Aid Procedures - Skin : - Eye : |
None normally encountered. Not determined, Expected to be low. Essentially non irritation or corneal. Mechanical injury only. Solid or dust may cause irritation or corneal injury due to mechanical action. Not Listed on NTP, IARC, OSHA Non normally encountered. Wash affected areas thoroughly with soap and water. Flush with clean, lukewarm water ( Low pressure) occasionally lifting eyelids. |
|
6. | PRECAUTION FOR SAVE HANDLING AND USE | |
Release and Spilled : Waste Disposal Method : Handling : Other Precaution : |
Sweep and mop or collect with vacuum cleaner Controlled burning. Wash thoroughly None. |
|
7. | CONTROL MEASURES | |
Respiratory Protection ( Specify Type ) : Ventilation. - Local Exhaust : - Mechanical ( General ) : Protective Gloves : Eye Protection : Other Protective Clothing or Equipment : Work Hygeienic Practices : |
Dust respirator. Desirable. Desirable. Rubber Goggles None Wash thoroughly after handling. |
|
THE DATA STATED HEREIN ARE BASED ON THE TEST RESULTS OF SIMILAR COMMERCIALLY AVAILABLE PRODUCT AND EXPIRIENCE WHICH THE MANUFACTURER BELIEVES RELIABLE AND ARE SUPPLIED FOR INFORMATION ONLY. THE PRODUCT IS INTENDED FOR SALING TO INDUSTRIAL AND COMMERCIAL CUSTOMERS. THE MANUFACTURER REQUESTS THAT CUSTOMERS INSPECT AND TEST THE PRODUCT BEFORE USE AND SATISFY THEMSELVES AS TO THE CONTENT AND SUITABILITY. |
PRODUCT DESCRIPTION: | TRIPPLE PRESSED STEARIC ACID |
||
PRODUCT CODE: | 1840 |
||
SPECIFICATION NO.: | -
|
||
PARAMETERS | SPECIFICATION |
METHODS |
|
ACID VALUE, mg KOH/g | - |
206 - 214 |
AOCS Te 1a - 64 |
SAPONIFICATION VALUE, mg KOH/g | - |
207 - 215 |
AOCS Tl 1a - 64 |
IODINE VALUE, g I2/ 100 g | - |
0.5 MAX |
AOCS Tg 1 - 64 |
TITER, °C | - |
54 - 57 |
AOCS Cc 12 - 59 |
COLOUR, APHA | - |
80 MAX |
AOCS Td 1b - 64 |
COLOUR, LOVIBOND 5.25" | RED YELLOW |
0.5R 2.0Y MAX |
AOCS Cc 13e - 92 |
CARBON CHAIN DISTRIBUTION, %WT | - |
- |
AOCS Ce 1 - 62 & AOCS Ce 2 - 66 |
C12 |
1 MAX |
||
C14 |
1 MAX |
||
C16 |
56 - 63 |
||
C18 |
37 - 42 |
||
C20 |
1 MAX |
||
UNKNOWN |
|||
ISSUED IN 1998. |
1. | COMPOSITION INFORMATION ON INGREDIENT(S) | |
Product Description : Product Code : Component : Chemical Formula : CAS No. : IUPAC Name : Exposure Guidelines : |
Triple Pressed Stearic Acid 1840 Fatty Acid, C16 - C18 CH3(CH2)nCOOH Hexadecanoic Acid - Octadecanoic Acid Mix Not Established |
|
2. | PHYSICAL CHEMICAL CHARACTERISTICS | |
Boiling Point : Freezing Point : Specific Gravity : Vapour Pressure : Vapour Density : Solubility : Appearance and Odor : |
~ 219 °C, 20 mmHg 50 - 60 °C 0.85 ( 70 °C ) Not applicable Not applicable Insoluble in water Soluble in alcohols, ethers, chloroform and acetone. White flake with slightly fatty oil like odor. |
|
3. | FIRE AND EXPLOSION HAZARD DATA | |
Flash Point ( Open Cup Method) : ~ Flammable Limit : Extinguishing Media : Special Fire Fighting Procedures : Unusual Fire and Explosion Hazard : |
~ 182 °C Not Applicable Water, Foam, Dry Chemical, CO2. Not Special Procedures None |
|
4. | REACTIVITY DATA | |
Stability : Incompatibility ( Material to Avoid ) : Hazardous Decomposition or By product : Hazardous Polymerization : |
Stable Strong oxidizing agent, Bases. CO on incomplete combusion. Will not Occur. |
|
5. | HEALTH HAZARTD DATA | |
Route(s) of Entry : Health Hazards ( Acute and Chronic ) - Ingestion toxicity : - Skin irritation : - Eye irritation : Carcinogenic : Signs and Symptoms of Exprosure : Emergency and First Aid Procedures - Skin : - Eye : |
None normally encountered. Not determined, Expected to be low. Essentially non irritation or corneal. Mechanical injury only. Solid or dust may cause irritation or corneal injury due to mechanical action. Not Listed on NTP, IARC, OSHA Non normally encountered. Wash affected areas thoroughly with soap and water. Flush with clean, lukewarm water ( Low pressure) occasionally lifting eyelids. |
|
6. | PRECAUTION FOR SAVE HANDLING AND USE | |
Release and Spilled : Waste Disposal Method : Handling : Other Precaution : |
Sweep and mop or collect with vacuum cleaner Controlled burning. Wash thoroughly None. |
|
7. | CONTROL MEASURES | |
Respiratory Protection ( Specify Type ) : Ventilation. - Local Exhaust : - Mechanical ( General ) : Protective Gloves : Eye Protection : Other Protective Clothing or Equipment : Work Hygeienic Practices : |
Dust respirator. Desirable. Desirable. Rubber Goggles None Wash thoroughly after handling. |
|
THE DATA STATED HEREIN ARE BASED ON THE TEST RESULTS OF SIMILAR COMMERCIALLY AVAILABLE PRODUCT AND EXPIRIENCE WHICH THE MANUFACTURER BELIEVES RELIABLE AND ARE SUPPLIED FOR INFORMATION ONLY. THE PRODUCT IS INTENDED FOR SALING TO INDUSTRIAL AND COMMERCIAL CUSTOMERS. THE MANUFACTURER REQUESTS THAT CUSTOMERS INSPECT AND TEST THE PRODUCT BEFORE USE AND SATISFY THEMSELVES AS TO THE CONTENT AND SUITABILITY. |
PRODUCT DESCRIPTION: | TRIPPLE PRESSED STEARIC ACID |
||
PRODUCT CODE: | 1850 |
||
SPECIFICATION NO.: | -
|
||
PARAMETERS | SPECIFICATION |
METHODS |
|
ACID VALUE, mg KOH/g | - |
205 - 209 |
AOCS Te 1a - 64 |
SAPONIFICATION VALUE, mg KOH/g | - |
206 - 210 |
AOCS Tl 1a - 64 |
IODINE VALUE, g I2/ 100 g | - |
0.5 MAX |
AOCS Tg 1 - 64 |
TITER, °C | - |
53 - 57 |
AOCS Cc 12 - 59 |
COLOUR, APHA | - |
80 MAX |
AOCS Td 1b - 64 |
COLOUR, LOVIBOND 5.25" | RED YELLOW |
0.5R 2.0Y MAX |
AOCS Cc 13e - 92 |
CARBON CHAIN DISTRIBUTION, %WT | - |
- |
AOCS Ce 1 - 62 & AOCS Ce 2 - 66 |
C12 |
1 MAX |
||
C14 |
2 MAX |
||
C16 |
43 - 50 |
||
C18 |
50 - 56 |
||
C20 |
1 MAX |
||
UNKNOWN |
|||
ISSUED IN 1998. |
1. | COMPOSITION INFORMATION ON INGREDIENT(S) | |
Product Description : Product Code : Component : Chemical Formula : CAS No. : IUPAC Name : Exposure Guidelines : |
Triple Pressed Stearic Acid 1850 Fatty Acid, C16 - C18 CH3(CH2)nCOOH Hexadecanoic Acid - Octadecanoic Acid Mix Not Established |
|
2. | PHYSICAL CHEMICAL CHARACTERISTICS | |
Boiling Point : Freezing Point : Specific Gravity : Vapour Pressure : Vapour Density : Solubility : Appearance and Odor : |
~ 291 °C, 100 mmHg 54 - 58 °C 0.84 ( 80 °C ) Not applicable Not applicable Insoluble in water Soluble in alcohols, ethers, chloroform and acetone. White flake with slightly fatty oil like odor. |
|
3. | FIRE AND EXPLOSION HAZARD DATA | |
Flash Point ( Open Cup Method) : ~ Flammable Limit : Extinguishing Media : Special Fire Fighting Procedures : Unusual Fire and Explosion Hazard : |
~ 182 °C Not Applicable Water, Foam, Dry Chemical, CO2. Not Special Procedures None |
|
4. | REACTIVITY DATA | |
Stability : Incompatibility ( Material to Avoid ) : Hazardous Decomposition or By product : Hazardous Polymerization : |
Stable Strong oxidizing agent, Bases. CO on incomplete combusion. Will not Occur. |
|
5. | HEALTH HAZARTD DATA | |
Route(s) of Entry : Health Hazards ( Acute and Chronic ) - Ingestion toxicity : - Skin irritation : - Eye irritation : Carcinogenic : Signs and Symptoms of Exprosure : Emergency and First Aid Procedures - Skin : - Eye : |
None normally encountered. Not determined, Expected to be low. Essentially non irritation or corneal. Mechanical injury only. Solid or dust may cause irritation or corneal injury due to mechanical action. Not Listed on NTP, IARC, OSHA Non normally encountered. Wash affected areas thoroughly with soap and water. Flush with clean, lukewarm water ( Low pressure) occasionally lifting eyelids. |
|
6. | PRECAUTION FOR SAVE HANDLING AND USE | |
Release and Spilled : Waste Disposal Method : Handling : Other Precaution : |
Sweep and mop or collect with vacuum cleaner Controlled burning. Wash thoroughly None. |
|
7. | CONTROL MEASURES | |
Respiratory Protection ( Specify Type ) : Ventilation. - Local Exhaust : - Mechanical ( General ) : Protective Gloves : Eye Protection : Other Protective Clothing or Equipment : Work Hygeienic Practices : |
Dust respirator. Desirable. Desirable. Rubber Goggles None Wash thoroughly after handling. |
|
THE DATA STATED HEREIN ARE BASED ON THE TEST RESULTS OF SIMILAR COMMERCIALLY AVAILABLE PRODUCT AND EXPIRIENCE WHICH THE MANUFACTURER BELIEVES RELIABLE AND ARE SUPPLIED FOR INFORMATION ONLY. THE PRODUCT IS INTENDED FOR SALING TO INDUSTRIAL AND COMMERCIAL CUSTOMERS. THE MANUFACTURER REQUESTS THAT CUSTOMERS INSPECT AND TEST THE PRODUCT BEFORE USE AND SATISFY THEMSELVES AS TO THE CONTENT AND SUITABILITY. |
1. | COMPOSITION INFORMATION ON INGREDIENT(S) | |
Product Description : Product Code : Component : Chemical Formula : CAS No. : IUPAC Name : Exposure Guidelines : |
Stearic Acid 65% 1865 Fatty Acid, C16 - C18 CH3(CH2)nCOOH Hexadecanoic Acid - Octadecanoic Acid Mix Not Established |
|
2. | PHYSICAL CHEMICAL CHARACTERISTICS | |
Boiling Point : Freezing Point : Specific Gravity : Vapour Pressure : Vapour Density : Solubility : Appearance and Odor : |
~ 291 °C, 100 mmHg 54 - 58 °C 0.84 ( 80 °C ) Not applicable Not applicable Insoluble in water Soluble in alcohols, ethers, chloroform and acetone. White flake with slightly fatty oil like odor. |
|
3. | FIRE AND EXPLOSION HAZARD DATA | |
Flash Point ( Open Cup Method) : ~ Flammable Limit : Extinguishing Media : Special Fire Fighting Procedures : Unusual Fire and Explosion Hazard : |
~ 182 °C Not Applicable Water, Foam, Dry Chemical, CO2. Not Special Procedures None |
|
4. | REACTIVITY DATA | |
Stability : Incompatibility ( Material to Avoid ) : Hazardous Decomposition or By product : Hazardous Polymerization : |
Stable Strong oxidizing agent, Bases. CO on incomplete combusion. Will not Occur. |
|
5. | HEALTH HAZARTD DATA | |
Route(s) of Entry : Health Hazards ( Acute and Chronic ) - Ingestion toxicity : - Skin irritation : - Eye irritation : Carcinogenic : Signs and Symptoms of Exprosure : Emergency and First Aid Procedures - Skin : - Eye : |
None normally encountered. Not determined, Expected to be low. Essentially non irritation or corneal. Mechanical injury only. Solid or dust may cause irritation or corneal injury due to mechanical action. Not Listed on NTP, IARC, OSHA Non normally encountered. Wash affected areas thoroughly with soap and water. Flush with clean, lukewarm water ( Low pressure) occasionally lifting eyelids. |
|
6. | PRECAUTION FOR SAVE HANDLING AND USE | |
Release and Spilled : Waste Disposal Method : Handling : Other Precaution : |
Sweep and mop or collect with vacuum cleaner Controlled burning. Wash thoroughly None. |
|
7. | CONTROL MEASURES | |
Respiratory Protection ( Specify Type ) : Ventilation. - Local Exhaust : - Mechanical ( General ) : Protective Gloves : Eye Protection : Other Protective Clothing or Equipment : Work Hygeienic Practices : |
Dust respirator. Desirable. Desirable. Rubber Goggles None Wash thoroughly after handling. |
|
THE DATA STATED HEREIN ARE BASED ON THE TEST RESULTS OF SIMILAR COMMERCIALLY AVAILABLE PRODUCT AND EXPIRIENCE WHICH THE MANUFACTURER BELIEVES RELIABLE AND ARE SUPPLIED FOR INFORMATION ONLY. THE PRODUCT IS INTENDED FOR SALING TO INDUSTRIAL AND COMMERCIAL CUSTOMERS. THE MANUFACTURER REQUESTS THAT CUSTOMERS INSPECT AND TEST THE PRODUCT BEFORE USE AND SATISFY THEMSELVES AS TO THE CONTENT AND SUITABILITY. |
Go Back Rubber Chemicals Center
Copyright © Rimpex@RPM Since 2002 www.rubberimpex.com Sitemap XIAMEN RPM IMP.&EXP. CO.,LTD. |